Nothing really beats using a super hot tool to melt bits of metal together into a single piece of hardcore wiring. The absolute strongest connection you can make for your strip lights is soldering the wires together. What is the most secure connection for my lights? With some patience and a little wiggling your lights should come on, if they don't, have no fear, these connectors can be tricky! give us a call at (225)-304-0408 and we will work with you to fix your specific issue! 5. Two positive ends (+) or two negative ends (-) won't work well together! With most issues, this polarity check should be enough to fix the problem, but if you're still experiencing an issue, there's more we can do to fix it! Once you know the polarities are right, carefully slide the strip back and forth in the clasp connector and try to make a more stable connection between the strip's ports and the connector's pins. The positive end (+) of the connectors should align with the positive end (+) of the strip, and the negative end (-) of the connector should be attached to the negative end (-) of the strip that your other strip is connecting to. Before anything else, check the connector's polarity and make sure that it aligns with BOTH strips that have been connected together. My LED’s worked before I connected them, but now they are off/dim!ĭon't worry, together we can fix this! This is an easily rectifiable problem, certainly not something that spells the end for your LED hopes and dreams. If the strip properly lights up, good job!Ĥ. If the strip doesn't light up, or if the diodes flicker, reopen the connector and start from the beginning as something was misaligned. Now that everything is properly aligned in the connector housing, close the clasp over the cut end of the strip. With the cut end of the strip in the connector, carefully line up the strip's copper ports underneath the clasp connector's silver connection pins. Once the connector has been opened up, slowly slide the cut end of the strip into the connector's open housing so that it fits snugly in the casing. Next you'll want to very carefully open up the end of the connector that aligns with the strips polarity, it is integral that you attach the correct polarity to your strip. Once you've made your careful cut along the pre-marked lines on your strip, peel away the 3M backing on the cut end of the strip. How do I use a strip with a clasp connector? If the any-angle connector doesn't have quite the reach you were looking for, then an extension connector is going to be your best bet! Before you buy any of these connectors though, check the product page to make sure it's compatible with your strip, as the connectors are not universal. If you're trying to make your strips take a sharp turn, or a strange angle, then any-angle connectors will give you just the kind of slack you need with a bit of flexible extension wiring. If you want your connected LED strip lights to have a seamless connection, so they look like a single strip when in use, then invisible connectors (also called LED strip to strip gapless connectors) are just what you're looking for to keep that consistent lighting you're so used to with strip lights. However, just because there isn't one answer doesn't mean the answers aren't simple to understand. There's unfortunately not one single answer, as I so often wish I could give in these Trouble Shooting guides. If you don't have or want to use a soldering tool, then you can use a Hitlights Strip Wiring/Connection Accessory! These accessories use clasp connectors that directly attach to the LED strips for simple and efficient connections! 2. If you've got the proper know how and tools, then feel free to directly solder the cut segment's wires together, and as always make sure you use good safety practices when working with tools. That's what you'll be connecting to other strips or wiring when you make the connection. Once you've made your safe cuts, you should be able to see some copper connection ports on the cut end. Well hold on! First thing's first, make sure you aren't just making wild cuts on the LED light strip, as cutting on a diode or other component can damage the strip, and more importantly, hurt you too! Our LED light strips have pre-marked lines on them exactly for the purpose of being cut on. How can I connect cut segments of LED Strip Lights?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |